Sat - Thu 9.00 AM - 6.00 PM
Wall Putty Exterior & Interior
Wall Putty
Exterior & Interior
Technical Data Sheet
Product Description:
MARKHOR Wall Putty is a high-quality, white
cement-based finishing material designed for smoothing walls and ceilings. It
provides an ideal base for paints and coatings by filling surface imperfections,
pores, and hairline cracks. Suitable for both interior and exterior applications,
it ensures a smooth, uniform surface with excellent bonding and durability.
Key Features & Benefits:
* High Adhesion: Excellent bonding to cement
plaster, concrete, and gypsum surfaces.
* Smooth Finish: Ideal for preparing
surfaces before painting.
* Water-Resistant: Suitable for humid and moistureprone areas.
* Crack-Resistant: Prevents shrinkage and cracking after drying.
*Eco-Friendly: Low VOC, non-toxic formulation.
* Ease of Application: Smooth,
creamy consistency for effortless spreading.
* Weather Durable: Suitable for
exterior exposure to sun and rain.
* Enhanced Paint Performance: Improves
the finish, coverage, and longevity of paint.
Applications:
Recommended for use on:
- Interior and exterior concrete walls
- Cement plaster and ceilings
- Fiber cement boards
- Pre-cast walls and ceilings
- Gypsum boards (after priming)
- Brickwork (plastered)
Technical Data:
| Property | Value |
|---|---|
| Appearance | White powder |
| Binder Base | White cement with polymer modifiers |
| Mixing Ratio | 4 – 5.5 liters of water per 25 kg bag |
| Pot Life | 2 – 3 hours at 25°C |
| Surface Dry Time | 30 – 60 minutes |
| Recoating Time | 6 – 8 hours |
| Application Thickness | 0.5 – 2 mm per coat |
| Coverage | Approx. 1.2 – 1.5 kg/m² at 1 mm thickness |
| Shelf Life | 12 months in unopened packaging |
| Storage Conditions | Store in a dry, covered area below 30°C |
Surface Preparation:
- Ensure the substrate is free of dust, grease, oil, loose
particles, and old paint. Dampen the surface with clean water before application.
Highly absorbent surfaces may require a primer or additional moistening to
avoid rapid water absorption.
Mixing Instructions:
1. Pour clean water into a container.
2. Gradually add MARKHOR Wall Putty powder while stirring.
3. Mix with a low-speed electric stirrer until a lump-free, creamy paste is formed.
4. Allow the mix to stand for 5 minutes, then remix before use
Application Procedure:
1. Apply with a putty knife or trowel in thin, even layers.
2. For best results, apply in two coats. Allow the first coat to dry before
recoating.
3. Lightly sand after final coat is dry for an ultra-smooth finish.
4. Allow sufficient curing before applying primer and paint.
Precautions & Safety Measures:
• Do not apply in direct sunlight or high humidity conditions.
• Use only clean tools and water for mixing.
• Avoid contact with skin and eyes.
• Use personal protective equipment (PPE) during handling and application.
• Wash hands thoroughly after use.
• Keep out of reach of children.
Compliance & Standards:
• Conforms to ASTM and EN standards for wall finishing materials.
• Produced under stringent quality control standards in accordance with
SASO regulations.
Packaging:
- 25 kg multi-layer paper bags with inner lining to protect from moisture.
Storage & Shelf Life:
- Store in original packaging in a dry and shaded area. Use within 12 months
from manufacture date.
Disclaimer:
The above information is based on laboratory and field experience and is believed to be correct. However, the company makes no warranties, expressed or implied, regarding the accuracy of this data. Users must determine suitability
for their own specific conditions. Saudi Markhor Industrial Company disclaims any liability arising from improper use of the product.
Compliance & Standard
• ISO 9001 : 2015 Compliant
• Our operations comply with the QFS-certified quality management system.
For technical support and inquiries, contact: Technical Support Department Saudi Markhor Industrial Company 059 110 9392 /
www.markhorsa.com
Material Safety Data Sheet
WALL PUTTY – 25 KG
Company: Saudi Markhor Industrial Company
1. Product and Company Identification
Product Name: Wall Putty Manufacturer: Saudi Markhor Industrial Company
Contact: 059 110 9392 Recommended Use: Surface preparation compound for
interior and exterior walls
2. Hazard Identification
Classification:
Not classified as hazardous under GHS.
Potential Health Effects:
May cause eye and skin irritation.
Environmental Effects: Not classified as environmentally hazardous.
3.Composition/Information on Ingredients
Ingredients:
- White Cement: 40-60%
- Polymers: 5-15%
- Fillers and Additives: 25-50%
- Preservatives: <1%
4. First Aid Measures
Eye Contact: Rinse cautiously with water for several minutes.
Skin Contact: Wash with plenty of soap and water.
Inhalation: Move to fresh air and keep at rest.
Ingestion: Do not induce vomiting. Seek medical advice.
5. Fire-Fighting Measures
Suitable Extinguishing Media: Water spray, foam, dry chemical.
Special Hazards: Non-combustible.
Protective Equipment: Wear self-contained breathing apparatus.
6. Accidental Release Measures
Personal Precautions: Use protective gloves and eye protection.
Environmental
Precautions: Avoid release to the environment.
Cleanup Methods: Sweep up and dispose of in accordance with regulations.
7. Handling and Storage
Handling:
Use in well-ventilated areas.
Avoid dust formation. Storage:
Store in a dry, cool place in original container.
8. Exposure Controls/Personal Protection
Eye Protection: Safety goggles.
Skin Protection: Protective gloves and clothing.
Respiratory Protection: Dust mask.
Ventilation: Ensure adequate ventilation.
9. Physical and Chemical Properties
Appearance: White powder Odor: Odorless
pH (when mixed with water): 12–13
Solubility: Slightly soluble in water
Boiling Point: Not applicable
Flash Point: Not applicable
10. Stability and Reactivity
Stability: Stable under normal conditions.
Conditions to Avoid: Moisture and humidity.
Incompatible Materials: Acids.
Hazardous Decomposition: None under normal use.
11. Toxicological Information
Acute Toxicity: Not classified.
Skin: May cause irritation.
Eyes: May cause serious irritation.
Inhalation: Prolonged exposure may cause respiratory irritation.
Method Statement
Application of Wall Putty – 25 KG Company: Saudi Markhor Industrial
Company
1. Scope of Work
- This method statement describes the procedure for the application of Wall Putty on interior and exterior surfaces to achieve a smooth and uniform finish suitable for subsequent painting or decorative coatings.
2. Materials Product:
Wall Putty (25 KG Bag) Manufacturer: Saudi Markhor
Industrial Company Description: A white cement-based polymer-modified wall
finishing material used to smoothen surfaces.
3. Tools and Equipment
- Mixing bucket or container
- Electric mixer o paddle
- Steel trowel / putty knife
- Sandpaper / sanding machine
- Clean water
- Safety gloves and goggles
4. Surface Preparation
• Ensure the surface is clean, dry, and free from dust, grease, or loose particles.
• Remove old paint, oil, or any contaminant that may reduce adhesion.
• Repair cracks or damaged areas before applying wall putty.
5. Mixing Procedure
• Pour clean water into a container.
• Slowly add wall putty powder to the water (approximately 2.5:1 powder
to water ratio).
• Mix thoroughly for 5–10 minutes until a smooth, lump-free paste is
achieved.
• Let the mix stand for 5 minutes before application.
6. Application Method
First Coat: - Apply the first coat evenly using a steel trowel.
- Allow it to dry for 6–8 hours under normal conditions.
Second Coat:
- Lightly sand the first coat with sandpaper.
- Apply the second coat uniformly.
- Allow it to cure for 24 hours before further treatment
like painting.
7. Curing and Finishing
• Do not overwater or wet the applied surface.
• Sand the final surface with fine sandpaper for a smooth finish.
• Ensure surface is dry before applying paint or topcoat.
8. Health and Safety
• Use appropriate personal protective equipment (PPE).
• Work in well-ventilated areas.
• Avoid contact with skin and eyes.
• In case of contact, rinse immediately with plenty of water.
• Refer to MSDS for detailed safety information.